Skip to content
CONMARBLENATURAL FINISHES Book a showroom tour
Home / Specify / Resin-bound surfacing / Addaset
Addaset resin bound aggregate paving along the promenade at Lusail Boulevard, Qatar
Resin-bound surfacing — technical data

Addaset

Resin bound surfacing

Manufacturer Addagrip Terraco Ltd
Country of origin United Kingdom
System family Resin-bound surfacing
Supplied and applied by Conmarble Natural Finishes

The product

The reference UV-stable resin bound system: a cold-applied clear polyurethane screed binding natural aggregate into a permeable, seamless surface course. BBA assessed, with published permeability figures a drainage engineer can design to.

Where it is used

  • Domestic driveways and patios
  • Pedestrian areas and footpaths
  • Lightly trafficked car parks
  • Low speed access roads
  • Promenades and landscape paving

Substrates

  • Concrete — clean, dry, free of laitance, oil, grease and loose friable particles
  • Asphalt — clean and dry, to a suitable base build-up
  • Movement and construction joints in concrete must be reflected through the surface
  • Edging in brick, stone, concrete or steel as required

Application data

Coverage, thickness, mix and cure, as declared by the manufacturer. Site conditions in the Gulf sit at the top of most of these ranges — allow for it in the programme.

Product Polyurethane resin for resin bound surfacing
Density 1.06 g/cm³
Application conditions +5 °C to 30 °C, maximum 80% relative humidity
Surface temperature Above 5 °C and 3 °C above dew point
Mixing Part A and B pre-weighed, Accelerator Part C added per the mix details sheet; mixed 45 seconds minimum, then 1–2 minutes with aggregate
Laying Spread with a straight-bladed squeegee, hand-trowelled or power-floated to a compacted finish
Anti-skid dressing Fine glass grit or white aluminium oxide at approx. 50 g/m², available on request
Initial cure Varies with accelerator addition
Full chemical cure 7 days
Packaging Pre-weighed units
Storage Above 7 °C, out of direct sunlight, wind and rain; 6 months unopened

Performance data

Every figure below is reproduced from the manufacturer's own technical data sheet, with the test standard it was measured against. The sheet itself is in the download section.

Property Result Standard
Third-party assessment BBA Agrément Certificate as a resin bound aggregate surfacing system for use as a surface course British Board of Agrément
Permeability — 3 mm aggregate 4.46 – 7.67 L/sec/m² at 12 mm depth BS EN 12697-40:2005
Permeability — 6 mm aggregate 7.39 – 20 L/sec/m² at 18 mm depth BS EN 12697-40:2005
Permeability — 10 mm aggregate 17 – 30 L/sec/m² at 22 mm depth BS EN 12697-40:2005
Skid resistance — pedestrian Slider 96 > 55 TRL 176
Skid resistance — vehicular Slider 57 > 60 TRL 176
Full chemical cure 7 days Addagrip data sheet

Where not to use it

The limits are as much a part of the specification as the performance. Everything here is stated on the manufacturer's data sheet.

  • Do not apply in wet conditions
  • Surface must be above 5 °C and at least 3 °C above the dew point
  • Natural aggregate colour and texture vary between batches; iron particles can cause rust spotting
  • Permeability depends on the whole build-up, not the surface course alone
Specification clause

Resin bound surfacing: Addagrip Addaset UV-stable polyurethane resin bound aggregate surface course, [10] mm aggregate laid [22] mm thick, blend and colour to the approved sample panel, over the base course specified. Permeability not less than [17] L/sec/m² to BS EN 12697-40:2005. Skid resistance to TRL 176, Slider 96 greater than 55. Substrate joints reflected through the surface. Edge restraint as detailed. 7 days full chemical cure before trafficking.

Square brackets mark the choices that belong to the project. Send us the finishes schedule and we will return the clause completed, with the sample and mock-up programme against it.

Documents

Every document is the manufacturer's own, reproduced in full and unaltered under our cover. Free to download, no form.

The rest of the resin-bound surfacing range

Addaset ECO Resin bound surfacing with recycled aggregate Addaset Non UVR Resin bound surfacing, non-UV-stable Addaset TP Polyurethane resin for tree pits Addacolor Coloured resin bound surfacing Addaflex R Resin bound rubber stone surfacing Addaflex R UV Resin bound rubber stone surfacing, UV-stable Stonebound UV Resin bound surfacing, UV-stable Stonebound Non UVR Resin bound surfacing, non-UV-stable Terrabase Resin bound surfacing, high permeability PU Addastone Resin bonded polyurethane surface dressing Addastone Thixotropic Agent Thickening filler

Technical support for the design team

We supply the material and we apply it, so the specification and the workmanship sit with one party. Send a finishes schedule, an elevation or a mood board and we will come back with the system, the build-up, the sample programme and a completed clause.

Send your finishes schedule Visit the showroom
Continue
Delivered projectsWhere this system is already installed.The specification hubEvery product, family and document in one place.Upload a scheduleSend a finishes schedule or bill of quantities for review.See it in personEvery range on real walls, by appointment.